Stepped/2-step lockers are two-tier lockers, usually available only in 15-inch (38-cm.) width; but the compartments and their doors have an L-shaped cross-section, which causes the division between the doors to follow a zigzag pattern. This configuration enables more hanging height to be included in both upper and lower lockers; but part of each compartment (the lower part of the upper one and the upper part of the lower one) will be only half the usual width of two-tier lockers.
Lockers are only available to currently enrolled students and current employees.  The University is not responsible for the contents of any locker.  Users must use the lock provided by Roosevelt University.  No stickers or posters are allowed on the lockers.  No dangerous or illegal items may be stored in lockers at any time.  Items causing unpleasant odors are not allowed.  Lockers must be able to be fully closed at all times.   Roosevelt University reserves the right to open lockers at its discretion at any time and to remove any items it believes compromises the safety or environmental quality of Roosevelt University.   Roosevelt University reserves the rights to charge for damages to the locker and may cancel this rental agreement at any time for any reason.

Locking options: various types of key locking or padlocking facility are available now. Key locking options include flush locks, cam locks, or locks incorporated into a rotating handle; padlocking facilities may be a simple hasp and staple, or else a padlocking hole may be included in a handle, often called a latchlock. More modern designs include keyless operation, either by coin deposit (which may or may not be returned when use of the locker terminates), or by using electronic keypads to enter passwords for later reopening the locker. Some older lockers used a drop-latch which was incorporated into the door handle, and slid up and down and could be padlocked at the bottom in the "down" position, but these are less used now. Three-point locking is not possible with this type of latch, because it needs to be operated by means of a latch that rotates rather than slides up and down; so this drop-latch is probably a less secure locking option, which may be why it is little used nowadays. Prefect Combination locks are very popular in school lockers used in the UK due to their ease of use and the time and cost saved in the removal of locker keys.
Denver has made strides in cleaning it's air but inversions still occur and trap all the crap we burn in the lower atmosphere. A big part of the brown cloud was particulate from sand spread on streets during the winter, that combined with car and truck pollution made for really bad air. Being a Trump support you likely cheer Trump's war on the EPA. Without action by the EPA Denver's air would be far dirtier than it is today. I hope the EPA works with Denver continue to work towards less pollution, especially ozone, which the Denver area is currently violating standards.

Gun lockers or safes are specifically designed for the secure storage of guns and ammunition. They broadly resemble normal single-tier lockers, but tend to be slightly less high than normal single-tier lockers, and are often free-standing, and not banked together. They are fitted with internal racks designed for holding firearms. They have a shelf at the top like normal single-tier lockers, although in this case it is closed and locked by a separate door, because of legal requirements in some countries that firearms and ammunition be stored and locked separately. They always lock with three-point locking, which is in some countries a legal requirement for the storage of firearms. Sometimes they are made of the standard kind of sheet steel used in manufacturing normal lockers, and sometimes they are made of extremely thick heavy-duty steel and in this case resemble a safe more than a normal locker. In Australia there are strict regulations governing the storage of firearms following the Port Arthur massacre in Tasmania, Australia on 28 April 1996, and cabinets used for storing firearms must be bolted to the floor or a wall if the cabinet is under a certain weight. Dedicated gun lockers are likely to include holes in the cabinet to accommodate such bolting. Several locker manufacturers also offer dedicated gun lockers.


At Shelving Rack & Lockers, Inc. we are always doing our part to recycle good industrial storage equipment. We are continually looking for quality used products that are in usable and sturdy condition. Doing so allows us to give you great products as well as incredible savings. Additionally, it helps us do our part to keep unnecessary items out of our landfills, making our environment more green.

Buy Locker Denver

×